====== Amplifier 13 ======
original source(([[http://en.blitzortung.org/Compendium/Documentations/Documentation_2014-05-11_Red_PCB_10.4_PCB_12.3_PCB_13.1_PCB_14.1.pdf|Documentation System RED]], chapter 4.2.2))

The amplifier/pre-amplifier system PCB 13 and PCB 14 is designed for an electric field antenna. The
system consists of an amplifier board (PCB 13) with three different filter systems and a pre-amplifier
board (PCB 14) with a very high input impedance. Any vertically oriented wire or copper plate
connected to the input of Pre-Amplifier PCB 14 can be used as e-field antenna.

The most important thing in building an e-field antenna is the search of the right site. Electric
antennas work best on non-developed areas. The utility frequencies of the main electricity is in general
between 50 Hz (Europe) or 60 Hz (America and parts of Asia). These frequencies, their harmonics,
and other very low frequencies are well filtered out by the high pass filter of pre-amplifier PCB 14 and
amplifier PCB 13. The combined high pass filter starts at 5 kHz and dims frequencies around 50 Hz
/60 Hz with more than 150 dB, see Figure 33.

{{:en:hardware:e-field_hp-filter.jpg?800|}}\\
Figure 33: The high pass filters of Pre-Amplifier PCB 14 and Amplifier PCB 13

The signals have to be filtered, because at certain regions the very low frequency range is disturbed
by various radio transmitters, see for exampleWikipedia.org/wiki/Very_low_frequency. These
signals can considerably disturb our measurements, on the one hand, because the lightning signals
can not be triggered and on the other hand, because the superposition can make it difficult to determine 
characteristic time stamps. The challenge is to find a filter that reduces most of the disturbances
without destroying the measurements. Obviously, there is no ideal filter that suppresses all types of
disturbances equally well. Amplifier PCB 13 has three different low pass filters, a 50KHz Bessel filter
to keep compatible to the H-field amplifier PCB 12, a sharper 44KHz elliptic filter, and a very ’rough’
18KHz elliptic filter, see Figure 34. The filtered signals can be used for different purposes. The signal
after the 50KHz Bessel filter is optimal for computing characteristic time stamps. The signals after
the 44KHz and 18KHz elliptic filters can be used to trigger in disturbed regions and for a more simple
computaton of the polarity. This is a feature which is possible with e-field antennas.

{{:en:hardware:e-field_lp-filter.png?800|}}\\
Figure 34: The low pass filters of Pre-Amplifier PCB 14 and Amplifier PCB 13

===== Electronic parts =====

The electronic parts necessary for Amplifier PCB 13 Version 1 are listed in Table 4.

| operational amplifiers | IC1, IC3, IC5, IC7 | MCP6S91 SMD SOI8 |
|  | IC2 | MCP6292 SMD SOI8 |
|  | IC4, IC6, IC8 | LMH6642 SMD SOI8 |
|  | IC9 | TLE2426 |
|  | IC10 | ATMega8 |
| LEDs | Power LED | LED 3mm (red) |
|  | Control LED | LED 3mm (green) |
|  | Gain LEDs 1,2,4,8 | LED 3mm (yellow) |
| Resistors, metal 1%, 0207 | R2, R11, R17, R23 | 100kΩ {{:en:hardware:r100k.png?80|}} |
|  | R5, R7 | 39kΩ {{:en:hardware:r39k.png?80|}} |
|  | R4 | 27kΩ {{:en:hardware:r27k.png?80|}} |
|  | R10, R16, R22 | 22kΩ {{:en:hardware:r22k.png?80|}} |
|  | R6 | 12kΩ {{:en:hardware:r12k.png?80|}} |
|  | R3, R12, R18, R24, R62 | 10kΩ {{:en:hardware:r10k.png?80|}} |
|  | R8, R9, R15, R21 | 1kΩ {{:en:hardware:r1k.png?80|}} |
|  | R60, R61 | 330Ω {{:en:hardware:r330.png?80|}} |
|  | R14 | 220Ω {{:en:hardware:r220.png?80|}} |
|  | R20 | 180Ω {{:en:hardware:r180.png?80|}} |
|  | R1 | 75Ω {{:en:hardware:r75.png?80|}} |
|  | R13, R19, R25| 47Ω {{:en:hardware:r47.png?80|}} |
| Resistor network, star, 6-1 | RN1 | 1kΩ A102 |
| Potentiometer | P1 | 50kΩ |
| Capacitors, electrolytic, 5mm | C62, C64 | 470 µF |
| Capacitors, electrolytic, 2mm | C17, C27, C37 | 2.2 µF |
| Capacitor, ceramic, 2.54mm | C1 | 220 nF (224) |
|  | C3, C4, C9, C13, C14, C15, C16, C23, C24, C25, C26, C33, C34, C35, C36, C60, C61, C63, C65 | 100 nF (104) |
|  | C30, C32 | 68 nF (683) |
|  | C20, C22, C29 | 33 nF (333) |
|  | C28 | 22 nF (223) |
|  | C18 | 15 nF (153) |
|  | C31 | 10 nF (103) |
|  | C12, C19 | 6.8 nF (682) |
|  | C7 | 4.7 nF (472) |
|  | C5 | 3.3 nF (332) |
|  | C11, C21 | 2.2 nF (222) |
|  | C8 | 1.5 nF (152) |
|  | C2, C6 | 1.0 nF (102) |
|  | C10 | 470 pF (471) |
| Inductors, radial, 5mm 09P | L8 | 4.7 mH |
|  | L6 | 2.2 mH |
|  | L5 | 1.5 mH |
|  | L3/L4 | 1 mH |
|  | L7 | 470/330 H |
| Inductors, axial SMCC | L2 | 3.3mH {{:en:hardware:l3_3m.png?80|}} |
| SMCC  | L1 | 1.5mH {{:en:hardware:l1_5m.png?80|}} |

Table 4: The list of electronic parts for Amplifier PCB 13 Version 1

{{:en:hardware:amplifier13.png?800|}}\\
Figure 35: Block diagram of Amplifier PCB 13 Version 1 and Pre-Amplifier 14 version 1

{{:en:hardware:pcb_13_1_sch.png?800|}}\\
Figure 36: The complete circuit diagram of Amplifier PCB 13 Version 1

{{:en:hardware:pcb_13_1_brd.png?800|}}\\
Figure 37: The Printed Circuit Board of Amplifier PCB 13 Version 1

{{:en:hardware:pcb_13_1_brd_b.png?800|}}\\
Figure 38: Assembly Diagram of Amplifier PCB 13 Version 1

===== Gain Control =====

The gain control is analogous to the gain control of amplifier PCB 12.

===== Connecting the controller =====

The RJ45 modular connector is used to connect the amplifier to the controller board. You should use
a shielded one-to-one CAT 5e network cable. The length of the cable can be up to 30 meters. This
allows us to place the amplifier near the antennas far away from noisy environments.

===== Output test pins =====

The output test pins can be used to monitor the output of the amplifier. This is useful if you want to
connect an oscilloscope or a sound card to analyze the VLF output without to disconnect the amplifier
from the controller board.

===== First hardware check =====

{{:en:hardware:amplifier13.1_assembled.png?800|}}\\
Figure 39: An assembled Amplifier PCB 13 Version 1